DIY TV Stand - A Blend Of Industrial Rustic And Modern - beplay体育网站下载,beplay苹果版app

ByEmily Burmeister| Published on2015年1月14日

of 19

DIY-TV-stand-from-galvanized-pipes

木材 - 电视台和 - 镀金台管

TV-Stand-how-to-stain-wood

how-to-stain-wood-TV-stand-diy

dark-wood-stain-TV-stand-finished

镀锌Pipes-tv-stand-sand-spray绘制

drilling-holes-for-TV-Stand

钻孔式式腿

电视台 - 腿部测试

电视台式训练

diy-tv-stand-legs-all-for

TV-stand-DVD-holder-smaller-pipes

TV-stand-with-galvanized-pipes-industrial-design

diy-tv-stand-with-with-with pipes fin

industrial-TV-stand-decor-above

wood-and-galvanized-pipes-tv-stand

镀锌管与电视固定式填充

diy工业 - tv-stand视图

rustic-and-modern-Tv-stand-last

DIY TV Stand - A Blend Of Industrial Rustic And Modern

Buy Now

TV-stand-with-galvanized-pipes-industrial-design

我回到我的老朋友：深木染了，galvanized pipes. It is such a cost effective and easy way to build furniture. Today I am creating aDIY TV stand.

使用这些用品可以让我拥有a rustic and industrial TV stand. Using a thinner wood will allow it to have a more modern feel to it. I’ve listed everything I used and laid out the steps so you can try making your ownDIY TV stand!

Materials Needed to Make DIY TV Stand:

x2 pine board 3.5x2ft
3/4″ pipe fittings
几个长度为3/4英寸的管道
弄脏
x4 base plates
screws

How to Make A DIY TV Stand with Pipes:

Step One: Choosing your board thickness

我从两个大型木板开始，它们是松树3.5 x 2英尺，厚约1英寸。我选择这使它尽可能地具有成本效益。选择板时，请务必选择一个足够坚固的板，以免电视的重量鞠躬。

Step Two: Stain

I sanded them up a little, allowing the wood stain to adhere to the surface as easy as possible. To stain anything be sure to wear gloves and lay something down so that the stain is just on the wood surface and not on anything else. Dipping a soft cloth into the stain, wringing it out in the can. And then wiping the stain on going side to side with the grain of the wood.

If there is dripping quickly wipe the drip into the wood until it has blended into the surface. After the wood is thoroughly stained. Take the cloth and wipe from one side to the other. Blending in the stain and making sure there is no wipe strokes left on the wood.

染色DIY电视摊的提示

对于这个特定的项目，我不得不弄脏木材的两面，因此等待它干燥之前，它真的很重要。您可以通过轻轻触摸木头来确定它是干燥的。如果您的手上有残留物或粘性，则不会干燥。

我希望能够看到这种木材中的谷物，从而允许结和天然木线透过。我通过进行较轻的污渍应用而实现了这一目标，并且只做一层涂层。

Step Three: Paint Pipes

在干燥的时候，我拿起了我购买的镀锌管，然后喷涂了黑色。我从一家家庭装修商店购买了这些管道，直径为3/4。beplay平台没信用这足以使腿有点有些陈述，足以固定木头。但是，不太大。

I spray painted them black in order for the contrast of wood and piping to pop.

Step Four: Drill Holes for the DIY TV Stand

Once the wood was dry it is time to drill in holes in the bottom piece of wood. The plan is for the pipes to go through the holes, connecting the legs, and wood to the top wood (where the TV will sit). I used a drill press to make the holes. Adding the bit to the end of it that was slightly larger than the 3/4 diameter pipes. This will allow the legs to slide through the hole.

Placing the wood up against the drill press as far as it can go. This gives me one easy way to measure where each hole should be. The wood is pressed up as far as possible to the press on the longer sides, no measuring needed. Then deciding how far in on the short sides I want the hole to go.

我决定使用4英寸。标记每个孔应该在哪里。慢慢将钻头推入现场。一直到另一侧创建一个孔。定期钻头也可以使用，并具有正确的钻头端。我在一个板上做了四个孔，这将是电缆和DVD盒架。钻孔完成后可能会有一些斑点要打磨和污渍，如果将某些污渍擦掉，则非常容易纠正。

Step Five: Assembling the DIY TV Stand

The next step is putting it all together. I simply slid the longer legs into the hole. Then set the top board over the holes. Tracing where they hit the top board. This shows me where to attach the top base of the pipes. Then connecting the shorter pipes to the circular base.

笔记: Be sure to get screws small enough for the width of your board. I needed to get special screws because the boards are somewhat skinny. And still had to be careful not to screw it too far and puncture the other side of the wood.

连接了前四个较小的管道。我有一个管道连接器，可以坐在下部板的底部。将板和管道固定在一起。将管道转动，直到它们紧密地连接在一起。

第六步：完成

Once they were connected I added small bottoms to the four legs, putting the cap on the bottoms. I was done. I set my TV and necessary equipment up and have a great industrial TV stand.

If I had purchased this it would have been a few hundred dollar at least. But I spent total $63 on this. I like that it is customizable to me and my needs. You could make it as tall, deep, or bulky as you want. Each person has a different room and needs within that room. Being able to create exactly what you need is much easier than making something work. Also, finding a way to get just what I wanted without spending as much is always a plus.

Finding a way to have industrial and warm mesh together is a great thing. Sometimes industrial with furniture can feel cold. The dark wood brings out a homey feel to the piece. And the simplicity of the TV stand allows it to work in a contemporary space just as nicely as a rustic or country space.